Screen Print & Inkjet BLAZER-PROTJB-1650 Manuel d'utilisateur Page 168
- Page / 200
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
T-Jet Blazer Series User’s Manual
Version 5.0 Revised September, 2008
152
Error Code: 10000
The fuse is blown (Express model) causing the print bed to sit on the index sensor.
Solution: You will need to replace the 5 amp fuse on the DC Motor Control Board. Follow the
instructions below.
Error Code 10000 Solution for the Blazer Express:
Replacing the DC Motor Control Board Fuse
What you will need
4 mm Allen Wrench•
Phillips Screwdriver•
5 amp fuse (supplied with printer)•
1. Remove the 6 screws on the left side access panel.
Caution: The side panel is not secured without the screws in place. The panel will fall if not
supported.
2. Locate the 5 amp fuse on the DC Motor Control Board.
- User’s Manual 1
- Copyright Notices 3
- A Letter from the 5
- Developer 5
- Table of Contents 7
- - Table of Contents 11
- Basic Safety 15
- Instructions 15
- Caution: 16
- Introduction 17
- The Basics 18
- Important Support Information 19
- About the Garment Decorating 20
- Our Advice 21
- Unpacking and Setup of 23
- Your Printer 23
- Blazer PRO SETUP 25
- Ground Support 26
- Locking Nut 26
- Placement of the Shirt Boards 27
- Final Unpacking Instructions 28
- The Bulk Ink System 29
- Ink Care 31
- Changing Ink Brands 31
- NON-GENUINE EPSON CARTRIDGE 32
- Interacting with the 33
- Blazer Express 33
- Main Power Switch 34
- Powering Off 35
- Blazer PRO 37
- Powering On 39
- Printer Driver 41
- Installation 41
- Technology 44
- Learning the LCD and 45
- User Interface Controls 45
- The LCD Display Icons 46
- User Interface Touch Screens 47
- BLAZER EXPRESS 49
- BLAZER PRO: 49
- BLAZER EXPRESS: 49
- Initialization Utilities 51
- MODE SELECT 52
- POSITION 53
- Shirt Board Height Settings 56
- BLAZER PRO 56
- FOR. REV 60
- (PRINT BED) 60
- Power Cleaning Utility 61
- PAPER OUT 62
- Nozzle Check Utility 63
- Head Cleaning Utility 64
- Print Head Alignment Utility 65
- BLAZER EXPRESS Setup 66
- IMPORTANT NOTE: If you 68
- BLAZER PRO - LFP Remote Panel 71
- BLAZER PRO Setup 72
- Quick Alignment (Optional) 81
- IMPORTANT NOTE: 83
- Software Overview 85
- FastARTIST and FastRIP 86
- Image Types 87
- Photoshop 88
- A Quick Note about Photoshop 89
- Check File Mode 89
- Check File Saturation 91
- Sharpening Images 91
- Using the Tone Curve 92
- Bitmap Editing in FastARTIST 93
- Selecting Areas 93
- Channels and Layers 93
- Using the Extract Filter 95
- FastARTIST 96
- Printing Basics 99
- WARNING 100
- Basic Printing Steps: 101
- IMPORTANT POINT 102
- Chapter 10 - Printing Basics 105
- WARNING: 106
- Printing Tips and Tricks 108
- Saving a Spooled Print File 109
- Canceling a Print Job 111
- LCD Display in Print Status 113
- “Paper Out/Roll Cut” 113
- Humidity Concerns 116
- Slight Discoloration 116
- Advanced Printing 117
- With White Ink 117
- IMPORTANT POINT: 119
- Types of Pretreatment 120
- File Setup 122
- Set Print Modes 122
- Washing Directions 124
- Maintenance 124
- Printing Other Items 127
- Adjusting the Platen Height 128
- Non-Textile Printing 129
- T-Jet Non-Textile Primer 130
- Printing on Golf Balls 133
- Information 134
- Non-Textile Printing Tips 135
- Daily, Weekly and Monthly 137
- 3. Clean the Wiper Blade 139
- 5. Clean the Print Head Area 139
- 7. Ink Levels and Care 140
- WASTE TANK FULL 141
- Monthly Maintenance 143
- DO NOT LUBRICATE DRIVE SCREW 144
- Tips and Utilities to 147
- Maximize Print Quality 147
- RAM and Your Computer 148
- No Windex on Clear Cover 148
- 1 to 3 Day Downtime 149
- 4 to 9 Day Downtime 149
- 9 Days or More Downtime 149
- Additional Utilities 150
- Print Head Replacement 152
- BEFORE AFTER 153
- Chapter 15 - Troubleshooting 155
- ► Clean the Capping Station 156
- 18. Wrong Print Location 165
- LCD Error Warnings and Codes 167
- Error Code: 10000 168
- Error Code: 10001 169
- Lead Screw 172
- Error Code: 1001D 173
- Error: TOP COVER OPEN 175
- Error: RELOAD PAPER 175
- 24 Hour Emergency Support 178
- Support on the Web 178
- Chapter 16 - Product Support 179
- Webcam Video Support 180
- Support 180
- Third Party Software Support 180
- Re-crating the Blazer EXPRESS 182
- Re-crating the Blazer PRO 184
- Step 4: Attach Upper Bracers 185
- Operational Guide 189
- The Customer must: 190
- Room Preparation 191
- Room Conditions 192
- Electrical Requirements 192
- Printer Specifications 193
- Miscellaneous Information 194
- Staging Area 195
- Uncrating 195
- Requirements and Notices 197
- Declaration of Conformity 198
- Limited Warranty 199
Produits connexes et manuels pour Imprimer et scanner Screen Print & Inkjet BLAZER-PROTJB-1650
(60 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels